Jump to content
krabi

Krabi's 525i E34 - vine red 1989

Recommended Posts

Just to update the works to date:

 

* interior vacuumed 

* front sport shocks and springs installed

* new wishbones, Track control arms, track rods, anti roll bar links installed 

* front discs and pads installed 

* rear sport shocks and springs installed 

* rear anti roll bar links and dog bones installed 

 

Rear discs, pads and handbrake shoes to be installed 

 

brake nipples, lines and fuel lines on order 

Share this post


Link to post
Share on other sites

Today the fuel tank was dropped and the vent pipes around it were replaced. The pipes were bent by hand and flared slightly on the ends to grip the hoses

 

Fuel hoses from tank to lines and filter were replaced with new and complimented with new fuel hose clamps. Fuel filter secured with big jubilee clip as mounted screw had broken off previously 

 

Middle section and back box installed. Rusty front support removed and added to shopping list 

 

Other items on shopping list Inc brake lines, brake hoses and fuel lines

Share this post


Link to post
Share on other sites

Going to be using this as my daily after Christmas so started undoing most of the work done in 2016 to replace the fuel lines, rear brake lines, rear brake dust shield (and therfore bearings).... And a little welding. 

 

Fuel tank dropped, exhaust off, dust shields off, drive shaft most of the way off

Share this post


Link to post
Share on other sites

Front to back brake lines done in Kunifer / Cupro nickel. I will be using one of the sellers that sell kits of ready made pipes on ebay for the next E34. 

 

Front to back fuel pipes also installed. I recommend using 8mm black coated aluminum as it is sooo much easier to form and you can mostly do it by hand. Completely messed up £38 of Cupro Nickel pipe. You have to use the forming tool. The 4m Krontec hard lines on ebay / demon tweeks will do the pipes to the filter but the longer pipe that connects to the vapour tank in the rear wheel well will need 4.3 - 4.5m worth.

Welding to the brake line / soft line anchor completed below the rear seat

IMG_20210411_192528.jpg

IMG_20210411_192455.jpg

IMG_20210411_192439.jpg

Share this post


Link to post
Share on other sites

New fuel pump relay installed, I had one go on a 518i touring so new bosch unit 0332209216 that turned out to be the same one used by :

 

BMW 61368373700
DAF 0095464
IVECO 0000042096498, 42069397, 42096498
MAN 81255020474, 81259020474
MERCEDES-BENZ 0005458485, 0015455405, 001545540564, 73751790000, A0005458485, A0015455405, A001545540564

Share this post


Link to post
Share on other sites

Fuel tank back in, heat shields re installed and wired / plumbed in. 

Old straps and rear axle were wire brushed and 'Kurusted' 

Old rear axle 'beer can' rubber mounts out. They were stamped 1997 so I only had to use the air hammer to push the sides in at the top and knock down working my way round. Got a question about installation that I'll post in the E34 section. 

New power Steering reservoir fitted and atf topped up

IMG_20210425_140834.jpg

IMG_20210425_140828.jpg

Share this post


Link to post
Share on other sites

New bushes / axle Carrier mounts are in after being in the freezer for 2 days and using Circolight rubber assembly fluid. I used my front wheel bearing kit and m14 rod / nuts / washers. Less than 5 minutes :-) pulled all the way in.

 

New handbrake cables in, what a faff. Rear part of the centre console had to come out to guide the cables home! 

 

Thinking ahead to emissions and the MOT ,  I noticed one of the hoses to the Idle control valve was split so a new one was installed. 

IMG_20210503_122638.jpg

IMG_20210503_123056.jpg

IMG_20210503_133524.jpg

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×