Jump to content

Owen540i

Members
  • Content count

    82
  • Joined

  • Last visited

  • Feedback

    100%

Everything posted by Owen540i

  1. Exhaust smoke in engine bay

    How is your intercooler pipe work below? Egr system pipework? Sent from my iPhone using Tapatalk
  2. 640d coupe opinions

    I was in BMW today the 640 GC is absolutely massive!! Sent from my iPhone using Tapatalk
  3. My Nemesis - Corsa Van 1.3CDTi

    Is anyone experienced with Vauxhall's or diagnostics, fancy offering your thoughts?? My van is a 2008 Vauxhall Corsa 1.3 CDTi 126k Miles. Fault: Car cut out when it was idling nicely after some recent engine repair work. Fault Codes Stored: - P0380 Glow Device Circuit Open Circuit P2146 Capacitor Voltage 1 Low Voltage P0087 Rail Pressure Low Pressure P1625 Main Relay Output Voltage Low Symptoms: - Fuel Pump cannot be heard priming at all. When cycling the key to start position it does not always engage the starter motor. Maybe 1 in 10 cycling of the key will get the starter moving like the ignition switch is faulty. Being rough with key helps. With live to the starter it spins perfectly. Compression is good, fires up and idles nicely on easy start. Timing appears perfect as all timing tools line up correctly. When using Op-Com to view live data in PCM there is no voltage reading shown, however in all other ECU’s the voltage is recorded accurately. Whilst there is no obvious water ingress into the PCM it is in the most ridiculous position!! I would really appreciate any pointers with the fault. Thanks Owen[emoji106] Sent from my iPhone using Tapatalk
  4. My Nemesis - Corsa Van 1.3CDTi

    You make a blunt but valid point[emoji12] Sent from my iPhone using Tapatalk
  5. Hello Everyone, I was hoping to gain some advice from the experts[emoji12]Have a few ideas below. The car is a 2006 137k miles, regularly serviced and almost all preventative maintenance carried out. Car is not as smooth or quiet is it has been on a cold start up, performance appears normal and mpg is well... crap as expected!! 10 minute scan on inpa revealed the following misdemeanours... P2620 Throttle position output circuit open. New throttle unit required or is a rebuild kit any good? Been there a while and consistent with shudder on turning off. 4212 Glow plug cylinder 1 Control 4232 Glow plug cylinder 3 Control 4242 Glow plug cylinder 4 Control- these codes have been consistent so perhaps the time for a controller and test plugs ? 4B90 Rail Pressure Monitoring at engine start. - I will look at this in live data in a variety of start up situations. 4185 Exhaust engine temperature sensor before Cat Signal. 4D00 Exhaust impression sensor. 480A System of particle filter - I will revisit last regent and check live data on DPF's condition. Assuming exhaust codes be related? P1278 Engine smoothness Control correction quantity too high. Perhaps an injector out of spec, I will check live data and put a leak off tester on it. Could be Time for all vacuum lines to be changed and some boost pipes show early signs of oily leaking from seals. 4A66 Power management Bordnet - Possibly IBS ? I have discharge message regularly when working on the car. Any help very much appreciated Owen Sent from my iPhone using Tapatalk
  6. 535d with a DDE full of fault codes!

    Had chance to work on the car today made some progress on the faults with more found for tomorrow. New Glow plug controller and replaced two of the plugs. **Those who tackle this with the inlet manifold on are quite frankly heroes!! Lost two M7 nuts in the process [emoji107] muppet!! Replaced all the crispy vacuum hoses, cleaned inlet out again, EGR and its throttle controller. Changed the wonky injector!! Found a leaking main thermostat seal. **Second Gates unit to fail to seal after a few months. I will check the cooling system more thoroughly and buy a genuine tomorrow. Found both front track Rods seized solid in the rod ends, no amount of heat would budge them. Have the parts to replace tomorrow and will align it. Battery is still required, has anyone moved from AGM to flooded? Wondering if the AGM is essential. Happy Days Sent from my iPhone using Tapatalk
  7. E60 Parts

    Hello Again, Please could you provide me some quotes for the following for a 2006 535d Vin B892450 1xDiesel Injector - 7792096 Main Battery - Currently have an AGM 95A 850Cca fitted. Main Thermostat Glow plug controller Thank you for your help Owen Sent from my iPhone using Tapatalk
  8. E60 Parts

    Hello, thank you for the quote. Could I check that the battery is an AGM? I will give you a call tomorrow. Owen Sent from my iPhone using Tapatalk
  9. 535d with a DDE full of fault codes!

    Little update Smooth/rough control issue are present due to correction values for cylinder 2 being through the roof at idle. Which would explain crap idle and unburnt diesel stench[emoji23] Best place to acquire an injector please?! Battery is being charged correctly when engine running but promptly discharges if you leave the boot open/ignition on for a short period with engine off. Best way to test an AGM battery? Standard drop tester adequate to condemn it? Thanks O Sent from my iPhone using Tapatalk
  10. 535d with a DDE full of fault codes!

    You may be onto something here sir ... Does it flag a code just for low temps? I have sadly fitted a gates main stat, it's the 2nd gates one due to sealing issues on first. On monitoring yesterday coolant temperatures were 97-103. Balls! Sent from my iPhone using Tapatalk
  11. 535d with a DDE full of fault codes!

    Thanks for your advice, my aim is to get into DIS this morning and check smooth running and DPF data. I think the evidence is stacking up for a new AGM battery. I have some time off in two weeks I will get inlet manifold off change vacuum lines and test/change Glow plug parts. Sent from my iPhone using Tapatalk
  12. Hello everyone, Recently increased from 20mm to 25mm spacers to the rear of my 535d m sport saloon to improve the look. Unfortunately there is a smidgen of rubbing on 19" spiders with large passengers and a fast roundabout! I am simply looking to flatten the inner lip this weekend to give me a few mm's. Any help appreciated O Sent from my iPhone using Tapatalk
  13. Has anyone rolled their rear arches?

    One of many of my scruffy old datsun's that with a few grand turned into extremely fun animals[emoji12] Sent from my iPhone using Tapatalk
  14. Has anyone rolled their rear arches?

    Car is standard M Sport ride height. Sent from my iPhone using Tapatalk
  15. Has anyone rolled their rear arches?

    I should have mentioned it's not my first attempt at arch rolling albeit not on anything as nice as my E60. Background in low wide skidding Nissans! The tyres are now closer to being flush but I would appreciate a bit more. 15mm spacers front and 25mm rear are ok I will get a few pictures. Sent from my iPhone using Tapatalk
  16. Has anyone rolled their rear arches?

    I have the oem 19" spiders I am unsure on the width or offset. I bought the arch roller so I will have a go on the weekend. My aim was to carefully flatten the internal lip and protect paintwork. Will check the arches are not full of filler first[emoji12] Sent from my iPhone using Tapatalk
  17. Had my 535D on the dyno this weekend!

    http://www.wagner-tuning.uk/200001060.html Sent from my iPhone using Tapatalk
  18. What did you do to your E60/61 today?

    Another Khumo advocate here been through two sets of KU39's on my 535d they are a good balance of cost and grip in my opinion. Used them on a few of my previous cars. [emoji106] Sent from my iPhone using Tapatalk
  19. Hello everyone, I am looking at improving the handling and specifically body roll on a 2006 130k 535d MSport. I don't expect it to handle like a go kart being a heavy old saloon. I also don't want compromise the ride quality overly or spend £2k on coilovers! I was wondering how useful or relevant you have found the following upgrades considering it's a pretty stiff chassis... ~Refreshing/upgrading bushes, arms, ball joints ~Upgraded anti roll bars possibly Eibach. ~lowering springs again possibly Eibach sportline. Any advice very much appreciated Owen Sent from my iPhone using Tapatalk
  20. Handling upgrade advice or opinions

    Balls not compatible with the active anti roll bar system I have fitted. I will do some more research. Sent from my iPhone using Tapatalk
  21. Handling upgrade advice or opinions

    My ARB bushes are getting sloppy so that's a great link thank you Dotcom1970. Willing to try the yellow just concerned they may transmit noise/vibrations if that are too firm Sent from my iPhone using Tapatalk
  22. Handling upgrade advice or opinions

    I have used the Eibach anti roll bars on previous cars and been impressed. Was wondering if they are worth the £350 on a 5 series. Sent from my iPhone using Tapatalk
  23. 535d Intercooler on 530d

    I wouldn't mind opinions from anyone who has fitted the Wagner Intercooler. It's been on my watch list for a little while[emoji12] It's part of an upgrade package I have been looking at for my 535d. Unsure where the standard Intercooler reaches its limit. Had great results from large fmic's on my past petrol cars. Sent from my iPhone using Tapatalk
  24. New tyre recommendations...

    I had a pair of budgets on the front of the car when I bought it and they cracked up on the inner sidewall just like the KU39's have. I have since been through a few sets of the Khumo's and haven't suffered with cracking. Well apart from the sh!te spiders which crack weekly!! Sent from my iPhone using Tapatalk
  25. Spacers

    Would you be willing to share where you got those from at such an excellent price please?! Sent from my iPhone using Tapatalk
×